A two pack polyamide cured epoxy sealer/primer for epoxy flooring systems over concrete

Product description

Epoxy – Sealer – Floor Coatings – A two pack polyamide cured epoxy sealer/primer for epoxy flooring systems over concrete substrates.

Properties and Areas of Use

-Tough, hard wearing film
-Good chemical resistance
-Excellent water resistance
-Used with low slip additive for floors and decks

Technical Coating Data @ 25 °C for mixed material

Finish                                                                          Flat

Color Range                                                               Transparent

Solids Volume                                                            55 ± 2%

Dry Film Thickness Range                                       50-150 µm

Theoretical Spreading Rate                                      5.5 m² / L @ 100 microns DFT
                                                                                       (loss factors will apply in practice)
Surface Dry                                                                 2 hours

Recoat Interval                                                          10 hours minimum
                                                                                      10 days Maximum.
Complete Cure                                                           7 days
Pot Life                                                                        6 hours
Flash Point                                                                 27°C
Shelf Life                                                                     12 months (stored in a cool dry place)
Mixing Ratio by Weight                                           8 Base component
                                                                                      1 Activator Component
VOC                                                                              360 g/l

Film Thickness and Spreading Rate:  

                                                                                  Minimum                            Maximum                          Typical
Film thickness, dry (µm)                                           50                                         150                                   100
Film Thickness, wet(µm)                                          91                                          228                                   182
Theoretical Spreading Rate (m2/L)                       11                                           3.67                                   5.5

Suitable Surfaces

 Steel and non ferrous metals properly prepared and blast cleaned to ISO-Sa2½
 Concrete free of contamination, dust and efflorescence, and properly prepared

Bare Steel:

Cleanliness: Blast – cleaning to Sa2 1/2 (ISO-8501-1:2007). Power tool cleaning to min. St2 (ISO 8501-
1:2007) may be acceptable, subject to exposure conditions.

Shopprimed Steel:

Clean, dry and undamaged approved shopprimer

Coated Surfaces:

Clean, dry and undamaged compatible primer .

Other Surfaces:

For aluminum substrates, thorough washing and sweeping with a nonmetallic blast medium is required.

Application Conditions

Substrate temperature should be 10°C or above for application and during cure and a minimum of 3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.

Application Information

Thinning should only take place after the two components have been thoroughly mixed.

Brush and Roller

Thin if required with 0-5% Paint Thinner Colorama TH907EP.

Conventional Air Spraying

– Thin with 5-25% Paint Thinner Colorama TH907EP, as required.
-Tip size – 2.0 mm
-Tip pressure – 60 psi (0.4Mpa) approximately

Airless Spraying

-Thin with 0-20% Paint Thinner Colorama TH907EP, as required
-Tip size – 0.58-.79 mm approximately
-Tip pressure – 2100 psi (15Mpa) approximately

Cleaning Thinner

Equipment should be cleaned immediately after use with Paint Thinner Colorama TH907EP.

Drying time:

Drying times are affected by air ventilation, temperature, film thickness and number of coats.
Substrate Temp.                                                                              10° C                              25° C                               40° C
Surface Dry                                                                                        4 h                                  2 h                                   1 h
Through Dry                                                                                     12 h                                 8 h                                   4 h
Dry to recoat, minimum                                                                 16 h                                10 h                                 6 h
The given data serve as guideline only. The actual drying time differs according to film thickness, ventilation, humidity and underlying paint system.


Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.

Paint System:

EPOSEAL 1 x 100 µ
SELFAPOX 1 x 3000 µ


Handle with care. Stir well before use.
Packing Size:                                               5 L & 18 L

Summary Safety Information

– Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other personal protection. Eyes should be cautiously washed with water or proprietary wash, and medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and water.
– Product is flammable
– No sparks or flames
– No smoking

Epoxy – Sealer – Floor Coatings


There are no reviews yet.

Be the first to review “EPOSEAL”

Your email address will not be published. Required fields are marked *

Shopping Cart
Open chat
Scan the code
Can we help you?