Product description
FINEPOX – GF Epoxy – Floor Coatings – Glass Flakes – Reinforced A solvent free two pack polyamine cured epoxy coating reinforced with glass flakes for water tank lining, fuel and chemicals tanks, steel structures and anti-chemicals flooring.
Properties and Areas of Use
– Tough hard wearing and flexible film.
– Suitable for marine and industrial atmospheric exposure, immersion and water tanks made of steel or concrete.
– Safe when used for food contact applications
– Cures at low temperatures
Technical Coating Data @ 25 °C for mixed material
Finish High Gloss
Color Range As per color card
Solids Volume 99 ± 1%
Dry Film Thickness Range 100-500 µm
theoretical Spreading Rate 10 m² / L @ 100 microns DFT
(loss factors will apply in practice)
Surface Dry 4 hours
Recoat Interval 12 hours minimum
10 days Maximum.
Complete Cure 7 days
Pot Life 1 hour
Flash Point > 100ºc
Shelf Life 12 months (stored in a cool dry place)
Mixing Ratio by Weight 3 Base component
1 Activator Component
VOC 0 g/l
Film Thickness and Spreading Rate:
Minimum Maximum Typical
Film thickness, dry (µm) 100 500 200
Film Thickness, wet(µm) 100 500 200
Theoretical Spreading Rate (m2/L) 10 2 5
Suitable Surfaces
Steel and non ferrous metals properly prepared and blast cleaned to ISO-Sa2½
Concrete free of contamination, dust and efflorescence, and properly prepared
Bare Steel:
Cleanliness: Blast – cleaning to Sa2 1/2 (ISO-8501-1:2007). Power tool cleaning to min. St2 (ISO 8501- 1:2007) may be acceptable, subject to exposure conditions.
Shopprimed Steel:
Clean, dry and undamaged approved shopprimer
Coated Surfaces:
Clean, dry and undamaged compatible primer .
Other Surfaces:
For aluminum substrates, thorough washing and sweeping with a nonmetallic blast medium is required.
Application Conditions
Substrate temperature should be 10°C or above for application and during cure and a minimum of 3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.
Application Information
No thinner needed for dilution.
Brush and Roller
Recommended
Airless Spraying
– No thinner needed
– Tip size – 0.58-.79 mm approximately
– Tip pressure – 2100 psi (15Mpa) approximately
Cleaning Thinner
Equipment should be cleaned immediately after use with Paint Thinner Colorama TH907EP.
Drying time:
Drying times are affected by air ventilation, temperature, film thickness and number of coats.
Substrate Temp. 10° C 25° C 40° C
Surface Dry 8 h 4 h 2 h
Through Dry 16 h 8 h 6 h
Dry to recoat, minimum 24 h 12 h 10 h
The given data serve as guideline only. The actual drying time differs according to film thickness, ventilation, humidity and underlying paint system.
Storage:
Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.
Paint System:
PRIMAPOX – GYM 1 x 75 µ (Steel) or EPOSEAL 1 x 100 µ (Concrete)
FINEPOX – GF 2 x 250 µ
Handling:
Handle with care. Stir well before use.
Packing Size:
5 L & 18 L
Summary Safety Information
-Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other personal protection. Eyes should be cautiously washed with water or proprietary wash, and medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and water.
– Product is flammable
– No sparks or flames
– No smoking
FINEPOX – GF Epoxy – Solvent Free – Floor Coatings – Glass Flakes – Reinforced
Reviews
There are no reviews yet.