Product description:
Joker Alkyd – Finish Coat Gloss – Fast Dry finishing coat for interior or exterior decorative, industrial and marine use.
Properties and Areas of Use
– Tough hard wearing film
– Low odor and excellent application properties
– Excellent color and gloss retention
– Excellent flow and opacity
– Used as a topcoat on steel in an anticorrosion alkyd system for industrial and marine applications.
Technical Coating Data @ 25 °C
Finish High Gloss
Color Range As per color card
Solid Volume 50 ± 2% depending on color
Dry Film Thickness Range 35-75 µm
Theoretical Spreading Rate 10 m² / L @ 50 microns DFT depending on
color (loss factors will apply in practice)
Surface Dry 2 hrs
Recoat Interval 16 hrs minimum
maximum, unlimited (after proper surface
cleaning and preparation)
Flash Point 38°C
Shelf Life 12 months (stored in a cool dry place)
VOC 405 g/L
Mixing Ratio Single Pack
Film Thickness and Spreading Rate :
Minimum Maximum Typical
Film thickness, dry (µm) 35 75 50
Film Thickness, wet (µm) 70 150 100
Theoretical Spreading Rate (m2/L) 14.3 6.67 10
Suitable Surfaces :
-Steel and non-ferrous metals properly blast cleaned to SIS-Sa 21/2 minimum
– Substrates must be free of contamination, dust, and efflorescence
– Previously gloss painted surfaces should be thoroughly abraded or sand blasted before application.
Bare Steel :
Cleanliness: Blast – cleaning to Sa2 1/2 (ISO-8501-1:2007). Power tool cleaning to min. St2
(ISO 8501-1:2007) may be acceptable, subject to exposure conditions.
Shop primed Steel :
Clean, dry and undamaged approved shop primer.
Coated Surfaces :
Clean, dry and undamaged compatible primer. For aluminum substrates, thorough washing
and sweeping with a nonmetallic blast medium is required.
Application Conditions :
Substrate temperature should be 10°C or above for application and during cure, and a
minimum of 3°C above the dew point. Adequate dry air ventilation is recommended for
optimum drying.
Application Information :
Thinning should only take place after the material has been thoroughly mixed.
Brush and Roller :
Thin if required with 0-5% COLORAMA Thinner 906 or 921.
Conventional Air Spraying :
– Thin with 5-15% COLORAMA Thinner 906 or 921, as required
– Tip size – 2.0 mm
-Tip pressure – 60 psi (0. 4Mpa) approximately
Airless Spraying :
-Thin with 0-10% COLORAMA Thinner 906 or 921, as required.
-Tip size – 13 thou (0.33mm) approximately
– Tip pressure – 1700 psi (12Mpa) approximately
Cleaning Thinner :
Equipment should be cleaned immediately Auer use with COLORAMA Thinner 906 or 921.
Drying time :
Drying times are affected by air ventilation, temperature, film thickness and number of
coats.
Substrate Temp. 10° C 25°C 40° C
Surface Dry 6 h 4 h 2 h
Through Dry 24 h 8 h 6 h
Dry to recoat, minimum 36 h 24 h 16 h
The given data serve as guideline only. The actual drying time differs according to film thickness,
ventilation, humidity and underlying paint system.
Typical paint system :
PRIMALKYD 1 x 50 µ.
JOKER Gloss 1 x 50 µ.
Storage :
Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition.
Containers must be kept tightly closed.
Handling :
Handle with care. Stir well before use.
Packing Size : 5 L & 18 L
Summary Safety Information :
-Avoid inhalation of spray mist and skin contact by the use of masks, gloves
and other personal protection. Eyes should be cautiously washed with
water or proprietary wash, and medical attention obtained. Skin should be
thoroughly washed using a cleanser and soap and water.
– Product is flammable
– No sparks or flames
– No smoking
Joker Alkyd – Finish Coat Gloss – Fast Dry
Reviews
There are no reviews yet.