3D primer

Product description

primer for 3D epoxy flooring systems New innovative flooring systems achieving the same protection of epoxy but in beautiful seamless 3D shapes.

Properties and Areas of Use

-Tough, hard wearing film
-Good chemical resistance
-Excellent water resistance
-Used with low slip additive for floors and decks

Technical Coating Data @ 25 °C for mixed material

Finish                                                                               Flat

Color Range                                                                    Transparent

Solids Volume                                                                 55 ± 2%

Dry Film Thickness Range                                           50-150 µm

Theoretical Spreading Rate                                         5.5 m² / L @ 100 microns DFT
(loss factors will apply in practice)
Surface Dry                                                                       2 hours

Recoat Interval                                                               10 hours minimum
10 days Maximum.
Complete Cure                                                                7 days
Pot Life                                                                             6 hours
Flash Point                                                                       27°C
Shelf Life                                                                           12 months (stored in a cool dry place)
Mixing Ratio by Weight                                                 8 Base component
1 Activator Component
VOC                                                                                     360 g/l

Film Thickness and Spreading Rate:

Minimum                                     Maximum                                      Typical
Film thickness, dry (µm)                                 50                                                       150                                           100
Film Thickness, wet(µm)                                 91                                                        228                                           182
Theoretical Spreading Rate (m2/L)               11                                                       3.67                                             5.5

Suitable Surfaces

 Concrete free of contamination, dust and efflorescence, and properly prepared

Application Conditions

Substrate temperature should be 10°C or above for applicaƟon and during cure and a minimum of
3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.

Application Information

Thinning should only take place after the two components have been thoroughly mixed.

Brush and Roller

Thin if required with 0-5% Paint Thinner Colorama TH907EP.

Conventional Air Spraying

-Thin with 5-25% Paint Thinner Colorama TH907EP, as required.
-Tip size – 2.0 mm
-Tip pressure – 60 psi (0.4Mpa) approximately

Airless Spraying

-Thin with 0-20% Paint Thinner Colorama TH907EP, as required
-Tip size – 0.58-.79 mm approximately
– Tip pressure – 2100 psi (15Mpa) approximately

Cleaning Thinner

Equipment should be cleaned immediately after use with Paint Thinner Colorama TH907EP.

Drying time:

Drying times are affected by air ventilation, temperature, film thickness and number of coats.
Substrate Temp.                                   10° C                                            25° C                                      40° C
Surface Dry                                              4 h                                              2 h                                           1 h
Through Dry                                            12 h                                             8 h                                          4 h
Dry to recoat, minimum                        16 h                                            10 h                                         6 h
The given data serve as guideline only. The actual drying time differs according to film thickness,
ventilation, humidity and underlying paint system.

Storage:

Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers
must be kept tightly closed.

Paint System:

• 3D Primer
  3D Basecoat
  3D Poster
  3D Topcoat

Handling:

Handle with care. Stir well before use.

Packing Size:                                 5 L & 18 L

Summary Safety Information

-Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other
personal protection. Eyes should be cautiously washed with water or proprietary wash, and
medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and
water.
-Product is flammable
-No sparks or flames
– No smoking
primer for 3D epoxy flooring systems