A two pack high quality polyamide cured coal tar epoxy coating.


Properties and Areas of Use

– Tough hard wearing flexible film
-Suitable for marine and industrial atmospheric exposure , immersion and water tanks
-Can be used with cathodic protection
-Cures at low temperatures

Technical Coating Data @ 25 °C for mixed material

Finish                                                                                          Egg Shell

Color Range                                                                               Brown Black

Solids Volume                                                                           65 ± 2%

Dry Film Thickness Range                                                      100-300 µm

Theoretical Spreading Rate                                                    6.5 m² / L @ 100 microns DFT

(loss factors will apply in practice)
Surface Dry                                                                                 6 hours

Recoat Interval                                                                          16 hours minimum

10 days Maximum.
Complete Cure                                                                           7 days
Pot Life                                                                                        6 hours
Flash Point                                                                                  27°C
Shelf Life                                                                                     12 months (stored in a cool dry place)
Mixing Ratio by Weight                                                           4 Base component

1 Activator Component
VOC                                                                                               415 g/l

Film Thickness and Spreading Rate:       

                                                                             Minimum                          Maximum                             Typical
Film thickness, dry (µm)                                        100                                       300                                    200
Film Thickness, wet(µm)                                        154                                        462                                    308
Theoretical Spreading Rate (m2/L)                      6.5                                        2.17                                    3.25

Suitable Surfaces

– Steel and non ferrous metals properly prepared and blast cleaned to ISO-Sa2½
-Concrete free of contamination, dust and efflorescence, and properly prepared

Bare Steel:

Cleanliness: Blast – cleaning to Sa2 1/2 (ISO-8501-1:2007). Power tool cleaning to min. St2 (ISO 8501-1:2007) may be acceptable, subject to exposure conditions.

Shop primed Steel:

Clean, dry and undamaged approved shop primer

Coated Surfaces:

Clean, dry and undamaged compatible primer .

Other Surfaces:

For aluminum substrates, thorough washing and sweeping with a nonmetallic blast medium is required.

Application Conditions

Substrate temperature should be 10°C or above for application and during cure and a minimum of
3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.

Application Information

Thinning should only take place after the two components have been thoroughly mixed.

Brush and Roller

Thin if required with 0-5% Paint Thinner Colorama TH907EP.

Conventional Air Spraying

– Thin with 5-25% Paint Thinner Colorama TH907EP, as required.
-Tip size – 2.0 mm
-Tip pressure – 60 psi (0.4Mpa) approximately

Airless Spraying

-Thin with 0-20% Paint Thinner Colorama TH907EP, as required
-Tip size – 0.58-.79 mm approximately
-Tip pressure – 2100 psi (15Mpa) approximately

Cleaning Thinner

Equipment should be cleaned immediately after use with Paint Thinner Colorama TH907EP.

Drying time:

Drying times are affected by air ventilation, temperature, film thickness and number of coats.
Substrate Temp.                                           10° C                       25° C                          40° C
Surface Dry                                                     10 h                          6 h                               4 h
Through Dry                                                   16 h                         12 h                             10 h
Dry to recoat, minimum                               24 h                       16 h                             12 h
The given data serve as guideline only. The actual drying time differs according to film thickness,
ventilation, humidity and underlying paint system.


Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers
must be kept tightly closed.

Paint System:

PRIMAPOX Zinc 2K                           1 x 75 µ
EPOXYTAR                                          2 x 200 µ


Handle with care. Stir well before use.

Packing Size:

5 L & 18 L

Summary Safety Information

– Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other
personal protection. Eyes should be cautiously washed with water or proprietary wash, and
medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and
-Product is flammable
-No sparks or flames
-No smoking



There are no reviews yet.

Be the first to review “EPOXYTAR”

Your email address will not be published. Required fields are marked *

Shopping Cart
Open chat
Scan the code
Can we help you?