PRIMABUILD-GF EPOXY TANK A two-pack high build polyamine cured epoxy paint, reinforced with glass flakes, which gives high film thickness at one coat. Used as a heavy duty, durable protection for tank lining, steel structures, bridges, off-shores, on-shores, metal decks and floors.
Properties and Areas of Use
-Tough abrasion resistant hard wearing film
– High chemical resistance
-Excellent water resistance
Technical Coating Data @ 25 °C for mixed material
Color Range Grey (other colors are available upon request)
Solids Volume 85 ± 2%
Dry Film Thickness Range 200-500 µm
Theoretical Spreading Rate 4.25 m² / L @ 200 microns DFT (loss factors will apply in practice)
Surface Dry 4 hours
Recoat Interval 12 hours minimum
7 days maximum
Complete Cure 7 days
Pot Life 2 hours
Flash Point 27°C
Shelf Life 1 2 months (stored in a cool dry place)
Mixing Ratio by Weight 4 Base component
1 Activator Component
VOC 126 g/L
PRIMABUILD-GF Film Thickness and Spreading Rate:
Minimum Maximum Typical
Film thickness, dry (µm) 200 500 250
Film Thickness, wet(µm) 235 588 294
Theoretical Spreading Rate (m2/L) 4.25 1.7 3.4
– Steel and non ferrous metals properly prepared and blast cleaned to ISO-Sa2½
-Concrete free of contamination, dust and efflorescence, and properly prepared
Cleanliness: Blast – cleaning to Sa2 1/2 (ISO-8501-1:2007). Power tool cleaning to min. St2 (ISO 8501-1:2007) may be acceptable, subject to exposure conditions.
Clean, dry and undamaged approved shopprimer
Clean, dry and undamaged compatible primer .
For aluminum substrates , thorough washing and sweeping with a nonmetallic blast medium is required.
Substrate temperature should be 10°C or above for application and during cure and a minimum of 3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.
Thinning should only take place after the two components have been thoroughly mixed.
Brush and Roller
Thin if required with 0-5% Paint Thinner Colorama TH907EP.
PRIMABUILD-GF Conventional Air Spraying
– Thin with 5-25% Paint Thinner Colorama TH907EP, as required.
– Tip size – 2.0 mm
– Tip pressure – 60 psi (0.4Mpa) approximately
– Thin with 0-20% Paint Thinner Colorama TH907EP, as required
– Tip size – 0.58-.79 mm approximately
– Tip pressure – 2100 psi (15Mpa) approximately
Equipment should be cleaned immediately after use with Paint Thinner Colorama TH907EP.
Drying times are affected by air ventilation, temperature, film thickness and number of coats.
Substrate Temp. 10° C 25° C 40° C
Surface Dry 8 4 2
Through Dry 16 8 6
Dry to recoat, minimum 24 12 8
The given data serve as guideline only. The actual drying time differs according to film thickness,
ventilation, humidity and underlying paint system.
Typical paint system:
PRIMAPOX – GYM 1 x 100 µ
PRIMABUILD – GF 2 x 250 µ
Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.
Handle with care. Stir well before use.
Packing Size: 5 L & 18 L
Summary Safety Information
– Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other personal protection. Eyes should be cautiously washed with water or proprietary wash, and medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and water.
– Product is flammable
-No sparks or flames
PRIMABUILD-GF EPOXY TANK