EPOSEAL – SF

EPOSEAL – SF-Epoxy – Sealer – Floor Coatings  A two pack solvent free polyamine cured epoxy bonding sealer for dry, damp and wet concrete to be
used as sealer/primer in epoxy flooring systems and can be used also as an adhesive to bond new and
old concrete together.

Properties and Areas of Use

-Tough, hard wearing film
-Good chemical resistance
-Excellent water resistance
-Used with low slip additive for floors and decks

Technical Coating Data @ 25 °C for mixed material

Finish                                                                          Flat
Color Range                                                               Transparent
Solids Volume                                                           99 ± 1%
Dry Film Thickness Range                                     50-150 µm
Theoretical Spreading Rate                                   13.3 m² / L @ 75 microns DFT
(loss factors will apply in practice)
Surface Dry                                                                2 hours
Recoat Interval                                                         2 hours minimum
10 days Maximum.
Complete Cure                                                           7 days
Pot Life                                                                        1 hour
Flash Point                                                                  >100°C
Shelf Life                                                                    24 months (stored in a cool dry place)
Mixing Ratio by Weight                                           5 Base component
1 Activator Component
VOC                                                                             0 g/l

Film Thickness and Spreading Rate:

                                Minimum                                Maximum                                 Typical

Film thickness, dry (µm)                                       50                                              150                                            75
Film Thickness, wet(µm)                                       50                                              150                                            75
Theoretical Spreading Rate (m2/L)                    20                                              6.67                                         13.3
Suitable Surfaces
 Concrete free of contamination, dust and efflorescence, and properly prepared

Application Conditions

Substrate temperature should be 10°C or above for application and during cure and a minimum of
3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.

Application Information

Now thinner needed as solvent free product.

Brush and Roller

Clean with Thinner Colorama TH907EP after application.

Conventional Air Spraying

-Clean with Thinner Colorama TH907EP after application.
-Tip size – 2.0 mm
-Tip pressure – 60 psi (0.4Mpa) approximately

Airless Spraying

-Clean with Thinner Colorama TH907EP after application .
-Tip size – 0.58-.79 mm approximately
-Tip pressure – 2100 psi (15Mpa) approximately

Cleaning Thinner

Equipments should be cleaned immediately after use with Paint Thinner Colorama TH907EP.

Drying time:

Drying times are affected by air ventilation, temperature, film thickness and number of coats.
Substrate Temp.                               10° C                        25° C                       40° C
Surface Dry                                          6 h                           2 h                            1 h
Through Dry                                        12 h                         4 h                            2 h
Dry to recoat, minimum                    4 h                           2 h                           1 h
The given data serve as guideline only. The actual drying time differs according to film thickness,
ventilation, humidity and underlying paint system.

Storage:

Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers
must be kept tightly closed.

Handling:

Handle with care. Stir well before use.

Packing Size:

5 L & 18 L

Summary Safety Information

 Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other
personal protection. Eyes should be cautiously washed with water or proprietary wash, and
medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and
water.
-Product is flammable
-No sparks or flames
-No smoking

EPOSEAL – SF-Epoxy – Sealer – Floor Coatings