FINEPOX – SG

Product description

FINEPOX SG – Epoxy – Solvent Free – Floor Coatings  two pack polyamine cured epoxy coating for water tank lining, fuel and chemicals tanks, steel structures and anti-chemicals flooring.

Properties and Areas of Use

– Tough hard wearing and flexible film.
-Suitable for marine and industrial atmospheric exposure, immersion and water tanks made of steel or concrete.
-Safe when used for food contact applications
-Cures at low temperatures

Technical Coating Data @ 25 °C for mixed material

Finish                                                                                    Semi-gloss
Color Range                                                                         As per color card
Solids Volume                                                                     99 ± 1%
Dry Film Thickness Range                                               100-500 µm
Theoretical Spreading Rate                                              10 m² / L @ 100 microns DFT
(loss factors will apply in practice)
Surface Dry                                                                          2 hours
Recoat Interval                                                                   12 hours minimum
10 days Maximum.
Complete Cure                                                                    7 days
Pot Life                                                                                  1 hour
Flash Point                                                                           > 100ºc
Shelf Life                                                                              24 months (stored in a cool dry place)
Mixing Ratio by Weight                                                   5 Base component
1 Activator Component
VOC                                                                                      4 g/L

Film Thickness and Spreading Rate:

                                                          Minimum                                             Maximum                                      Typical

Film thickness, dry (µm)                                                                    100                                                          500                                              200
Film Thickness, wet(µm)                                                                    100                                                          500                                              200
Theoretical Spreading Rate (m2/L)                                                   10                                                              2                                                     5

Suitable Surfaces 

 Steel and non ferrous metals properly prepared and blast cleaned to ISO-Sa2½
 Concrete free of contamination, dust and efflorescence, and properly prepared

Bare Steel:

Cleanliness: Blast – cleaning to Sa2 1/2 (ISO-8501-1:2007). Power tool cleaning to min. St2 (ISO 8501-1:2007) may be acceptable, subject to exposure conditions.

Shopprimed Steel:

Clean, dry and undamaged approved shopprimer

Coated Surfaces:

Clean, dry and undamaged compatible primer .

Other Surfaces:

For aluminum substrates, thorough washing and sweeping with a nonmetallic blast medium is required.

Application Conditions

Substrate temperature should be 10°C or above for application and during cure and a minimum of 3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.

Application Information

No thinner needed for dilution.

Brush and Roller

Recommended

Airless Spraying

-No thinner needed
-Tip size – 0.58-.79 mm approximately
-Tip pressure – 2100 psi (15Mpa) approximately

Cleaning Thinner

Equipment should be cleaned immediately after use with Paint Thinner Colorama TH907EP.

Drying time:

Drying times are affected by air ventilation, temperature, film thickness and number of coats.
Substrate Temp.                                                                 10° C                                           25° C                                              40° C
Surface Dry                                                                            4 h                                               3 h                                                  2 h
Through Dry                                                                          12 h                                              8 h                                                  6 h
Dry to recoat, minimum                                                      16 h                                             12 h                                                10 h
The given data serve as guideline only. The actual drying time differs according to film thickness,
ventilation, humidity and underlying paint system.

Storage:

Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.

Handling:

Handle with care. Stir well before use.

Packing Size:

5 L & 18 L

Summary Safety Information

– Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other
personal protection. Eyes should be cautiously washed with water or proprietary wash, and
medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and
water.
-Product is flammable
-No sparks or flames
-No smoking
FINEPOX SG – Epoxy – Solvent Free – Floor Coatings