A solvent free, zero VOC polyamine adduct cured epoxy paint reinforced with zircon and corundum grains to
maximize the impact and abrasion resistance. ABRAPOX (high wear epoxy) has high abrasion resistance, high
chemical resistance, gives high film thickness at one coat designed to provide cost effective resistance to
particle impact abrasion with a high degree of flexure and vibration. ABRAPOX protects relatively large flat
areas from abrasive attack. It is easily applied on-site, and also applied to more complex areas. It is ideally
suited for application to: cyclones, hoppers, deflector screens, wear plates, burner barrels, mixing blades,
bunkers, pipe bends and process equipment.

ABRAPOX  Properties and Areas of Use

– Tough hard wearing and flexible film.
– Suitable for marine and industrial atmospheric exposure, immersion and water tanks made of steel or concrete.

ABRAPOX  Technical CoaƟng Data @ 25 °C for mixed material

Finish                                                                                                       Egg shell

Color Range                                                                                            As per color card

Solids Volume                                                                                         99 ± 1%

Dry Film Thickness Range                                                                    1-12 mm

Theoretical Spreading Rate                                                                  0.54 m² /Kg @ 1000 microns DFT (loss factors will apply in practice)
Surface Dry                                                                                               2 hours

Recoat Interval                                                                                         4 hours minimum
3 days Maximum.

Complete Cure                                                                                          7 days
Pot Life                                                                                                       45 min.
Flash Point                                                                                                > 100ºc
Shelf Life                                                                                                    24 months (stored in a cool dry place)
Mixing Ratio by Weight                                                                          6 Base component
1 Activator Component
VOC                                                                                                              0 g/l

ABRAPOX  Film Thickness and Spreading Rate:             

                                                                                                              Minimum                     Maximum                   Typical
Film thickness, dry (µm)                                                                         1000                                 12000                        5000
Film Thickness, wet (µm)                                                                        1000                                 12000                         5000
Theoretical Spreading Rate (m2/Kg)                                                     0.54                                 0.045                           0.11

Suitable Surfaces

 Steel and non ferrous metals properly prepared and blast cleaned to ISO-Sa2½
 Concrete free of contamination, dust and efflorescence, and properly prepared

Bare Steel:

Cleanliness: Blast – cleaning to Sa2 1/2 (ISO-8501-1:2007). Power tool cleaning to min. St2 (ISO 8501-1:2007) may be acceptable, subject to exposure conditions.

Shopprimed Steel:


Clean, dry and undamaged approved shop primer

Coated Surfaces:

Clean, dry and undamaged compatible primer .

Other Surfaces:

For aluminum substrates, thorough washing and sweeping with a nonmetallic blast medium is required.

ABRAPOX  Application Conditions

Substrate temperature should be 10°C or above for applicaƟon and during cure and a minimum of 3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.

Application Information

No thinner needed for dilution.

Application Tools

Metal Trowels

Cleaning Thinner

Equipment should be cleaned immediately after use with Paint Thinner Colorama TH907EP.

Drying time:

Drying times are affected by air ventilation, temperature, film thickness and number of coats.
Substrate Temp.                                        10° C                        25° C                       40° C
Surface Dry                                                  6 h                           4 h                            3 h
Through Dry                                               12 h                           8 h                           6 h
Dry to recoat, minimum                           18 h                          10 h                          8 h
The given data serve as guideline only. The actual drying time differs according to film thickness, ventilation, humidity and underlying paint system.


Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.


Handle with care. Stir well before use.

Packing Size:                                               5 Kg, 20 Kg & 25 Kg
Summary Safety Information

– Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other personal
protection. Eyes should be cautiously washed with water or proprietary wash, and medical
attention obtained. Skin should be thoroughly washed using a cleanser and soap and water.
– Product is flammable
– No sparks or flames
– No smoking


There are no reviews yet.

Be the first to review “ABRAPOX”

Your email address will not be published. Required fields are marked *

Shopping Cart
Open chat
Scan the code
Can we help you?