Product description
ACRYNIL Varnish- Polyurethane Transparent acrylic gloss varnish with outstanding hardness, chemical resistance and elasticity. The high mechanical and chemical resistance of this product makes it suitable for the application as a glossy or matt topcoat for almost any wood works for internal and external use
Properties and Areas of Use
– Tough, hard wearing flexible film, with excellent hardness, color retention and weathering resistance
-Good chemical resistance, and excellent water resistance
-Cures at low temperatures
Technical Coating Data @ 25 °C for mixed material
Finish High Gloss, Semi-Gloss or Matt
Color Range Transparent
Solids Volume 40 ± 2%
Dry Film Thickness Range 25-75 µm
Theoretical Spreading Rate 8 m² / L @ 50 microns DFT
(loss factors will apply in practice)
Surface Dry 30 min.
Recoat Interval 4 hours minimum
10 days maximum
Complete Cure 5 days
Pot Life 2 hours
Flash Point 28°C
Shelf Life 12 months (stored in a cool dry place)
Mixing Ratio by Weight 2 Base component
1 Activator Component
VOC 732 g/L
Film Thickness and Spreading Rate:
Minimum Maximum Typical
Film thickness, dry (µm) 25 75 50
Film Thickness, wet(µm) 63 188 125
Theoretical Spreading Rate (m2/L) 16 5.3 8
Suitable Surfaces
– Steel and non ferrous metals properly prepared and blast cleaned to ISO-Sa2½
– Concrete free of contamination, dust and efflorescence, and properly prepared
-Wood must be abraded with sand paper No. 320 and primed with PU or polyester wood sealer
Application Conditions
Substrate temperature should be 10°C or above for application and during cure and a minimum of 3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.
Application Information
Thinning should only take place after the two components have been thoroughly mixed. Brush and Roller Thin if required with 0-5% Paint Thinner Colorama TH908UE.
Conventional Air Spraying
– Thin with 5-25% Paint Thinner Colorama TH908UE, as required.
– Tip size – 2.0 mm
-Tip pressure – 60 psi (0.4Mpa) approximately
Airless Spraying
– Thin with 0-20% Paint Thinner Colorama TH908UE, as required
-Tip size – 0.58-.79 mm approximately
-Tip pressure – 2100 psi (15Mpa) approximately
Cleaning Thinner
Equipment should be cleaned immediately after use with Paint Thinner Colorama TH908UE.
Drying time:
Drying times are affected by air ventilation, temperature, film thickness and number of coats.
Substrate Temp. 10° C 25° C 40° C
Surface Dry 1 h 30 min. 15 min.
Through Dry 4 h 2 h 1 h
Dry to recoat, minimum 12 h 4 h 2 h
The given data serve as guideline only. The actual drying time differs according to film thickness, ventilation, humidity and underlying paint system.
Typical paint system:
FONDAL Sealer 2 x 100 µ
ACRYNIL Varnish 2 x 50 µ
Storage:
Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition. Containers must be kept tightly closed.
Handling:
Handle with care. Stir well before use.
Packing Size: 5 L & 18 L
Summary Safety Information
– Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other
personal protection. Eyes should be cautiously washed with water or proprietary wash, and
medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and
water.
-Product is flammable
-No sparks or flames
-No smoking
ACRYNIL Varnish- Polyurethane
Reviews
There are no reviews yet.