COLUX SILVER -colorama coatings- marine coatings

Product description

COLUX SILVER – Alkyd – Finish Coat – Enamel – Gloss for interior or exterior decorative, industrial and marine use. Formulated to resist salty water, weather and yellowing.

Properties and Areas of Use:

• Tough hard wearing film.
• Low odor and excellent application properties.
• Excellent color and gloss retention.
• Excellent flow and opacity.
• Used as a topcoat on steel in an anticorrosion alkyd system for industrial and marine applications.

Technical Coating Data @ 25 °C

Finish:                                                                   Gloss

Color Range:                                                        Silver

Solids Volume:                                                    48 ± 2% depending on color

Dry Film Thickness Range:                              35-75 µm

Theoretical Spreading Rate:                             13.7 m² / L @ 35 microns DFT depending on color (loss factors will apply in practice).

Surface Dry:                                                         2 hrs

Recoat Interval:                                                  16 hrs minimum maximum, unlimited (after proper surface                                                                                             cleaning and preparation).

Flash Point:                                                          38°C

Shelf Life:                                                              12 months (stored in a cool dry place).
VOC:                                                                       438 g/L
Mixing Ratio:                                                        Single Pack

Film Thickness and Spreading Rate :   

                                                                             Minimum                 Maximum                  Typical

Film thickness, dry (µm):                                      35                                  75                             50
Film Thickness, wet(µm):                                      73                                 156                            104
Theoretical Spreading Rate (m2/L):                    13.7                              6.4                            9.6

Suitable Surfaces :

• Steel and non-ferrous metals properly blast cleaned to SIS-Sa 21/2 minimum.
• Substrates must be free of contamination, dust, and efflorescence.
• Previously gloss painted surfaces should be thoroughly abraded or sand
  blasted before application.

Bare Steel :

Cleanliness: Blast – cleaning to Sa2 1/2 (ISO-8501-1:2007). Power tool cleaning to min. St2 (ISO 8501-1:2007) may be acceptable, subject to exposure conditions.

Shop primed Steel :

Clean, dry and undamaged approved shop primer.

Coated Surfaces :

Clean, dry and undamaged compatible primer. For aluminum substrates, thorough washing and sweeping with a nonmetallic blast medium is required.

Application Conditions :

Substrate temperature should be 10°C or above for application and during cure, and a minimum of 3°C above the dew point. Adequate dry air ventilation is recommended for optimum drying.

Application Information :

Thinning should only take place after the material has been thoroughly mixed.

Brush and Roller :

Thin if required with 0-5% COLORAMA Thinner 906 or 921.

Conventional Air Spraying :

• Thin with 5-15% COLORAMA Thinner 906 or 921, as required.
• Tip size – 2.0 mm.
• Tip pressure – 60 psi (0. 4Mpa) approximately.

Airless Spraying :

• Thin with 0-10% COLORAMA Thinner 906 or 921, as required.
• Tip size – 13 thou (0.33mm) approximately.
• Tip pressure – 1700 psi (12Mpa) approximately.

Cleaning Thinner :

Equipment should be cleaned immediately after use with COLORAMA Thinner 906 or 921.

Drying time :

Drying times are affected by air ventilation, temperature, film thickness and number of coats.

Substrate Temp.:                                                               10°C                     25°C                  40°C
Surface Dry:                                                                         6 h                        4 h                      2 h
Through Dry:                                                                       24 h                    8 h                      6 h
Dry to recoat, minimum:                                                   36 h                    24 h                    16 h

The given data serve as guideline only. The actual drying time differs according to film thickness, ventilation, humidity and underlying paint system.

Typical paint system :

• Marine Primer:                                                     2 x 50 µ.
• COLUX Silver:                                                      1 x 50 µ.

Storage :

Keep the containers in a dry, cool, well ventilated space and away from source of heat and ignition.

Handling :

Handle with care. Stir well before use.

Packing Size :

5 L & 18 L

Summary Safety Information :

• Avoid inhalation of spray mist and skin contact by the use of masks, gloves and other personal protection. Eyes should be cautiously washed with water or proprietary wash, and medical attention obtained. Skin should be thoroughly washed using a cleanser and soap and water.
• Product is flammable.
• No sparks or flames.
• No smoking.

COLUX SILVER – Alkyd – Finish Coat – Enamel – Gloss